Dreame Z10 Pro filter
The Dreame Z10 Pro takes the Dreame Filter (Z10 Pro, L10s Ultra, D10s Plus, L10 Prime, L10s Plus, D10 Plus Gen 2) (part DRE-FTLR) as its filter; replace it every 3 months; Australian sellers list it from A$38.95 as of 1 August 2026. Fitment confirmed against the manufacturer's compatibility list.
Appliance confirmed before purchase
Not yours? Change
Your robot vacuum
Dreame Z10 Pro
Robot vacuum · Z series
Takes this filter
Filter (Z10 Pro, L10s Ultra, D10s Plus, L10 Prime, L10s Plus, D10 Plus Gen 2)
DRE-FTLR
The right filter for Z10 Pro
Dreame Filter (Z10 Pro, L10s Ultra, D10s Plus, L10 Prime, L10s Plus, D10 Plus Gen 2)
- Replace every 3 months
- Fits inside the fridge
- Fits 6 models
The washable dust-box filter for the Z10 Pro, L10s Ultra, L10s Plus, L10 Prime, D10s Plus and D10 Plus Gen 2. Lift the top lid, pull the bin, and the filter lifts off the back of it. Rinse it fortnightly, let it dry a full day, and replace it when it stays grey.
Reduces
- Fine dust and allergens blown back into the room
- Pack
- 2 filters
- Washable
- Yes — rinse, no detergent, dry 24 h
- Dreame cycle
- Replace every 1-3 months
- Dreame part
- DRE-FTLR
Every number this part goes by
Where to buy
Every seller we track for this part, cheapest first. Genuine is the manufacturer's own part; compatible is a third-party filter made to fit. Prices are re-checked daily where the seller publishes them. Last checked 1 August 2026.
How long it lasts
Replace every 3 months — the app reminds you.
After fitting: In the Dreame app open Maintenance, tap Filter and choose Reset after fitting the new one.
Flow slows and taste drops off as the filter fills up. Changing on time is the whole point of the filter.
Not due yet?
This filter is due every 3 months. We'll email you when it's time — free, no spam.
Fitting it
A few minutes, no tools. Watch it done, then follow the steps.
- 1Lift the robot's top lid and pull the dust box out by its handle.
- 2Press the clip on the back of the box and lift the old filter off.
- 3Clip the new filter on with the pleats facing the box, close the box and slide it back until it clicks.
- 4In the Dreame app open Maintenance, tap Filter and choose Reset.
About your Dreame Z10 Pro
Dreame robot vacuum, robot vacuum — Z series. Its filter is the Filter (Z10 Pro, L10s Ultra, D10s Plus, L10 Prime, L10s Plus, D10 Plus Gen 2), part DRE-FTLR, changed every 3 months.
Also in this robot vacuum: Dreame Dust Bag 4L (Z10 Pro) (every 2 months), Dreame Main Brush (Z10 Pro) (every 12 months), Dreame Mop Pad (Z10 Pro, D10 Plus) (every 6 months), Dreame Side Brush (Z10 Pro) (every 3 months). Worth replacing together — one job, not two.
Checking the model number: Turn the robot over: the model name and serial are on the label on the underside. The model name is also on the top lid of most robots.
Fits these models
Common questions
- Which filter fits the Dreame Z10 Pro?
- The Dreame Z10 Pro takes the Dreame Filter (Z10 Pro, L10s Ultra, D10s Plus, L10 Prime, L10s Plus, D10 Plus Gen 2) (part DRE-FTLR). Compatible filters made to the same specification also fit.
- How often should I replace the filter in my Dreame Z10 Pro?
- Every 3 months. Flow slows and performance drops off as the filter fills up, so it's worth doing on time.
- Where can I buy the DRE-FTLR in Australia?
- We track 3 Australian sellers for the DRE-FTLR; the lowest listed price when we last checked was A$38.95 at robot_specialist. Prices are re-checked daily and dated on this page.
- How do I fit the DRE-FTLR in a Dreame Z10 Pro?
- No tools, a few minutes: 4 steps, listed on this page with the replacement video where the maker has one.
Own a Z10 Pro and this looks wrong? . Reports go to a person, not a bot.