Shark ZU62 filter
The Shark ZU62 takes the Shark HEPA Filter for ZU62 (XHFZU62ANZ) (part XHFZU62ANZ) as its filter; replace it every 12 months; Australian sellers list it from A$37.99 as of 1 August 2026. Fitment confirmed against the manufacturer's compatibility list.
Appliance confirmed before purchase
Not yours? Change
Your vacuum cleaner
Shark ZU62
Stick vacuum · Navigator
Takes this filter
HEPA Filter for ZU62 (XHFZU62ANZ)
XHFZU62ANZ
The right filter for ZU62
Shark HEPA Filter for ZU62 (XHFZU62ANZ)
- Replace every 12 months
- Fits inside the fridge
- Fits 1 model
Shark's genuine XHFZU62ANZ for the ZU62: the post-motor filter behind the cover on the main body, the last stage before the exhaust. Shark's part page lists the fit; both filter stages are washable and the part is for when they no longer come clean or are damaged.
- Fits
- ZU62
- Washable
- Yes - rinse yearly, dry 24 h
- Shark part
- XHFZU62ANZ
Every number this part goes by
- Retail name:
- XHFZU62
Where to buy
Every seller we track for this part, cheapest first. Genuine is the manufacturer's own part; compatible is a third-party filter made to fit. Prices are re-checked daily where the seller publishes them. Last checked 1 August 2026.
How long it lasts
Replace every 12 months.
After fitting: Shark: rinse filters in water only (no soap), squeeze out and air-dry for at least 24 hours before refitting; a damp filter can damage the motor. No reset.
Flow slows and taste drops off as the filter fills up. Changing on time is the whole point of the filter.
Not due yet?
This filter is due every 12 months. We'll email you when it's time — free, no spam.
Fitting it
A few minutes, no tools. Watch it done, then follow the steps.
- 1Unplug the vacuum and lift the dust cup off.
- 2Unclip the filter grille low on the front of the base and lift it off.
- 3Pull the old HEPA filter out, push the new one in and refit the grille until it clicks.
- 4Rinse the HEPA filter yearly and let it dry 24 hours before refitting.
About your Shark ZU62
Shark vacuum cleaner, stick vacuum — Navigator. Its filter is the HEPA Filter for ZU62 (XHFZU62ANZ), part XHFZU62ANZ, changed every 12 months.
Also in this vacuum cleaner: Shark Pre Motor Foam and Felt Filter Kit for ZU62 (XFFKZU62ANZ) (every 12 months). Worth replacing together — one job, not two.
Checking the model number: The rating label is on the underside or the back of the main body; the bag or filter type is usually printed on the old part.
Fits these models
Shark1 model
Common questions
- Which filter fits the Shark ZU62?
- The Shark ZU62 takes the Shark HEPA Filter for ZU62 (XHFZU62ANZ) (part XHFZU62ANZ). Compatible filters made to the same specification also fit.
- How often should I replace the filter in my Shark ZU62?
- Every 12 months. Flow slows and performance drops off as the filter fills up, so it's worth doing on time.
- Where can I buy the XHFZU62ANZ in Australia?
- We track 1 Australian seller for the XHFZU62ANZ; the lowest listed price when we last checked was A$37.99 at shark_au. Prices are re-checked daily and dated on this page.
- How do I fit the XHFZU62ANZ in a Shark ZU62?
- No tools, a few minutes: 4 steps, listed on this page with the replacement video where the maker has one.
Own a ZU62 and this looks wrong? . Reports go to a person, not a bot.